Annotation: The pyrobolts, or explosive bolts, belong to the pyrotechnical devices with monolithic case consisting o f the cap, as a rule with hexagonal surface, and of cylindrical part with thread. The pyrobolts are separated into parts using the pyrotechnical charge placed inside the case. Owing to the simple design, reliability and short action time, the pyrobolts have found wide application in aerospace engineering for separation of assemblies and bays, in particular, stages, head modules, launching boosters, etc. So, for example, about 400 pyrobolts are used in the Proton launch vehicle. The designs of pyrobolts are markedly different. By method of explosive substance action on case structural elements, the pyrobolts are divided into two types: the pyrobolts using the shock wave formed at detonation of brisant explosive substance for case wall destruction and the pyrobolts using the pressure of gases arising at pyrotechnical charge blasting. By method of separation into parts, they are divided into fragmenting pyrobolts with ridge-cut, with piston, and shear pyrobolts. The paper deals with the design of various types of pyrobolts, their disadvantages are considered. The Yuzhnoye SDO-developed pyrobolt of shear type with segments is presented that uses radial shear forces of segments located in the hole of cylindrical part to separate the case parts. The above segments a re actuated using a rod with sealing rings and a piston connected to the rod through a rubber gasket; the piston moves under pressure of gases formed during pyro cartridge action. The following calculations are presen ted: strength analyses with determination of case load-carrying capacity; power analyses with justification of pyro cartridge selection for pyrobolt actuation. In the developed pyrobolt of shear type with segments, the case parts are separated without considerable shock loads and without high-temperature gases and fragments release into environment, ensuring reliable separation of bays and assemblies without damaging sensitive equipment.

Annotation: One of the systems in the integrated launch vehicle responsible for prelaunch processing and launch is a ground thermal conditioning system, which supplies the low-pressure air into the launch vehicle’s “dry” compartments. Thermal conditioning system is mated with the launch vehicle, using the mating interfaces, proper functioning of which enhances reliability of the ground support equipment, the launch vehicle and the entire space launch system. The article describes key requirements to the interfaces of the thermal conditioning system and the drawbacks of the existing designs. The article proposes a new design concept of the interface that connects the pipeline of the ground thermal conditioning system to the orifice of the launch vehicle using the corrugated rubber hose composed of three basic parts, attached with the help of a metal lock/release assembly. The proposed solution provides reliable leaktightness, ease of operation, providing multiple connections to the launch vehicle, including at various angles, and automatic disconnection by rocket motion or manual removal in case of launch abort. Using rubber as a high-elasticity structural material to manufacture the hoses, enabled minimization of efforts required to disconnect the interface from the launch vehicle. In its high-elasticity state, rubber can absorb and dissipate mechanical energy within a wide range of temperatures, which prevents transmission of engine vibrations to the ground thermal conditioning system. The article presents key properties of rubber used as a structural material and its peculiarities to be considered during design of similar products. Unlike metal showing two types of deformation (elastic and plastic), rubber can exhibit three types of deformation (elastic, superelastic and plastic). In the process of interface design, we took into account two types of deformations (elastic and superelastic ones). Experimental studies of the interface showed its full compliance with technical specification.

Annotation: Explosive bolts are widely used as actuating devices in the spacecraft separation systems. Explosive bolt body is divided into parts as a result of engagement of the pyromixture placed inside. Activated explosive bolts have negative mechanical effect on the interface elements and sensitive electronic devices installed nearby owing to explosive behavior of the pyromixture combustion, generating shock front with high pressure and velocities, impacts and collisions of the structural units. Cumulative effect of the above factors on the separated objects is called pyroshock. For separation systems with increased requirements to external actions and cleanliness, authors developed a shear explosive bolt or pyrobolt, divided into parts, cutting the body walls in segments, which are set in motion by action of the pressure of gases, released as a result of pyrocartridge activation. The basic sources of pyroshock for these shear explosive bolts with segments are: combustion of pyromixture, internal impacts of structural units against the bolt body; cutting of body wall in segments, release of preliminary deformed interface after activation. Structural solutions are presented to reduce the pyroshock per each of the components. Vibration impulsive loading during pyromixture combustion is reduced by optimization of explosive quantity, finding its minimum to provide the reliable activation of the device. To reduce the impact on the explosive bolt elements and shock front interface the rubber gasket is installed in the path of shock wave distribution, partially disseminating and absorbing its kinetic energy. Damper, made of easily deformable aluminum alloy, is also installed to decrease the internal impact of the rod against the explosive bolt body. Functional testing of the device, using the pendulum suspension and measuring separation speed and vibration impulsive loading, showed that body parts of the shear explosive bolt with segments are separated without significant impact loads and discharge of high-temperature gases and debris, providing reliable separation of compartments and units without damaging the sensitive equipment. Obtained values of the mechanical momentum, I = 0,4÷0,7 N•s and shock load spectrum – g-load 1950 g at the frequency range up to 5000 Hz, meet the up-to-date requirements to pyrotechnical devices.