Annotation: The article analyzes the energy potential of alternative sources of Ukraine. The projects using hydrogen technologies aimed at attracting solar energy to the infrastructure of energy technological complexes, in particular water desalination systems and for refueling automobile vehicles located in areas with high solar radiation potential, are considered. During the operation of water desalination plants using a solar power station as an energy source, contingencies are very likely to arise due to either a power outage (due to cloudy weather) or an emergency failure of individual elements of the system. In this case, it is required to ensure its removal from service without loss of technological capabilities (operability). For this purpose, it is necessary to provide for the inclusion in the technological scheme of the energy technological complex of an additional element that ensures operation of the unit for a given time, determined by the regulations for its operation. As such an element, a buffer system based on a hydrogen energy storage device is proposed. The current level of hydrogen technologies that are implemented in electrochemical plants developed at the Institute of Mechanical Engineering named after A. N. Podgorny of the National Academy of Sciences of Ukraine allows producing and accumulating the hydrogen under high pressure, which eliminates the use of compressor technology.

Annotation: The process of creating modifications of aircraft in the transport category is a very relevant and widespread phenomenon in modern aircraft construction. A separate group of military transport aircraft has been distinguished in connection with the specific character of their mission: – the need to formulate the characteristics “cargo – range” for light, medium, operational tactical and strategic military transport aircraft, since it is precisely according to this characteristic that they are positioned by their purpose; –specific requirements are imposed on military transport aircraft cargo compartment not only with respect to its geometrical dimensions and usable volume, but also with respect to the possibility of simultaneous accommodation of military equipment and people, as well as the placement of a stretcher with t he wounded during their evacuation from the war zone; – the possibility of airborne landing of military equipment and paratroopers, which requires specific hatches and means of maintaining weight balance in flight; – the possibility of basing on poorly prepared sites with a runway length of less than 800 m in the short take-off and landing (STL) mode, especially for operational tactical military-technical vehicles, which significantly expands their use in combat zones; – the possibility of conversion into a civilian aircraft: for the delivery of goods to areas of the far north, when fighting fires, when evacuating victims from disaster zones, etc. The article shows that creation of modifications of expensive military transport aircraft is the main direction of their development. All leading aircraft manufacturing companies in the world use modification procedures as the way to most quickly meet constantly changing requirements for military transport aircraft. Along with the traditional methods of designing the modifications, the domestic school proposed a new methodology for determining the necessary parameters for “deep” modifications in wing geometry and propulsion system. The methodology is based on the use of three principles: – ensuring growth of carrying capacity and the required range of modifications of military transport aircraft of various purposes; – geometric re-arrangement of wing and system of carrying surfaces “wing + tail units” according to the criterion of minimum inductive resistance when lifting forces are equal to basic version; – coordination of modifications in wing with the required parameters of propulsion system as a condition for ensuring the required fuel efficiency.

Annotation: The main parameters are understood as: carrying capacity mг, range L and fuel efficiency qт, which largely determine the competitiveness of aircraft of this type, including military transport aircraft. The reason for the creation of modifications of transport category aircraft is the requirement for a constant increase in their flight performance by increasing the carrying capacity and range. Among the main goals of implementing such decisions there is an indispensable increase in the fuel efficiency of modifications, since the cost of fuel reaches 80 % of the cost of an airplane hour during operation. There are a number of models that make it possible to assess the influence of the weight and aerodynamic parameters of the airframe of the aircraft and the fuel performance of the power plant (specific engine consumption) on the integral indicator of the fuel efficiency of the modification at cruising mode and the average hourly fuel consumption at the certification stage, when all parameters of the airframe and engine are fixed and consideration of options is not possible. A new model is proposed for the stage of designing modifications, in which deep modification changes are made in the geometry of wing and in the power plant with various variants of their correlation and coordination. The parameters of new model: specific fuel efficiency – specific route productivity, in order to form the relative carrying capacity and relative range of action for the required specific fuel efficiency. An analysis of such dependencies showed: – with an increase in relative range L , fuel costs per flight also increase; – the adequacy of changes in route performance is observed only at L < 0.5. At L > 0.5 productivity is constantly decreasing, while the specific indicator of fuel consumption per unit of work increases exponentially; – if in the analysis we take into account the specific value of transport efficiency, that is, the characteristic “load – range” ( mп.н  f L ), it becomes obvious that the most favorable (from the point of view of fuel efficiency) are relative ranges of 0,3 < L < 0,5. In this range L , not only acceptable fuel efficiency values are realized, but also the maximum value of the route performance, that is the main parameters for which modifications are developed.

Annotation: Basic dynamic properties of the reentry part of the aircraft-type first stage were examined when turbojet engine is used in the recovery phase. Such configuration can be of interest because turbojets have considerably smaller rate of flow in comparison to rocket engines. Moreover, they are launched in the lower stratosphere or in the troposphere so that there is no need to place oxidizer supply on board. This recovery plan differs from an alternative rocket recovery system and, from our point of view, provides more efficient usage of the fuel stores because it doesn’t require the main propulsion to be started in the recovery phase. Besides the analysis of qualitative characteristics of the descend phase for this stage, the efficiency of a wing with moderate values of maximum aerodynamic characteristics and a turbojet was studied. In this case three ways for stage recovery were investigated. The first one implied unguided descend with zero angle of attack assuming that the stage is statically stable. This descend trajectory was considered as standard and was used to evaluate the efficiency of the wing and turbojet with relatively small propulsion. The second and the third design cases offered the gliding guided descend with turbojet being started only in the lower stratosphere. The last two cases used the same program for the angle of attack. The possibility to ensure permissible overload values at the critical points of the descend trajectory and acceptable values of kinematic characteristics at the earth surface tangency point are also of great interest. Thereby the program for the angle of attack was developed in a way that allowed kinematic characteristics on touchdown be as close as possible to the corresponding values, shown by civil and/or military-transport heavy aircraft. Simulation was conducted on Microsoft Visual Studio 2010.

Annotation: In the present-day rocket engineering, the liquid rocket engines with pump feed system have gained wide acceptance. As a rule, the pumps used in liquid rocket engines are screw-axifugal. The screw serves to increase pressure upstream of the axifugal wheel, thus ensuring its cavitation-free operation. The screws used in the screw-axifugal pumps of liquid rocket engines may be of two types: with constant and variable step. The screws with constant step are easier to calculate, profile and manufacture as compared to the screws with variable step. As known from the literature, the use of the screw with variable step increases power characteristics of the screw-axifugal pump. The purpose of investigation is comparative analysis of cavitation and power characteristics of the following high-speed low-consumption screw-axifugal pumps of liquid rocket engines with jointed screws, screws of constant and variable step:  RD868 engine oxidizer and fuel pumps;  RD859 engine fuel pumps;  RD861K engine fuel pumps. Besides, the analysis has been made of the impact of design features and geometrical dimensions of the screws with variable and constant step on power characteristics of the screw-axifugal high-speed lowconsumption pumps of liquid rocket engines. Special attention has been given to the analysis of anticavitation properties of the pumps with screws of variable step and pumps with jointed screws. Based on the results of investigation, it has been ascertained that when using the joint screws and screws with variable step instead of the screws with constant step in the high-speed low-consumption screw-axifugal pumps of liquid rocket engines, the pump delivery head increases from 0.65 to 3.83%, the efficiency increases up to 1.7%. The use of jointed screw and screw of variable step as compared with the screw of constant step does not have any impact on cavitation properties of low-consumption crew-axifugal pumps of liquid rocket engines.