Annotation: The scientific and methodological propositions for the designing single-stage guided missiles with the solid rocket motors for advanced multiple launch rocket systems are defined. The guided missiles of multiple launch rocket system are intended for delivering munitions to the given spatial point with required and specified kinematic motion parameters at the end of flight. The aim of the article is an analysis of the development trends of the guided missiles with the solid rocket motors for the multiple launch rocket systems, identifying the characteristics and requirements for the flight trajectories, design parameters, control programs, overall dimensions and mass characteristics, structural layout and aerodynamic schemes of missiles. The formalization of the complex task to optimize design parameters, trajectory parameters and motion control programs for the guided missiles capable of flying along the ballistic, aeroballistic or combined trajectories is given. The complex task belongs to a problem of the optimal control theory with limitations in form of equa lity, inequality and differential constraints. To simplify the problem, an approach to program forming is proposed for motion control in the form of polynomial that brings the problem of the optimal control theory to a simpler problem of nonlinear mathematical programming. When trajectory parameters were calculated the missile was regarded as a material point of variable mass and the combined equations for center-of-mass motion of the guided missile with projections on axes of the terrestrial reference system were used. The structure of the mathematical model was given along with the calculation sequence of the criterion function that was used for determination of the optimal parameters, programs and characteristics. The mathematical model of the guided missile provides adequate accuracy for design study to determine depending on the main design parameters: overall dimensions and mass characteristics of the guided missile in general and its structural comp onents and subsystems; power, thrust and consumption characteristics of the rocket motor; aerodynamic and ballistic characteristics of the guided missile. The developed methodology was tested by determining design and trajectory parameters, overall dimensions and mass characteristics, power and ballistic characteristics of two guided missiles with wings for advanced multiple launch rocket systems produced by the People’s Republic of China, using the limited amount of information available in the product catalog.

Annotation: The article gives the analysis results for the servo drives dynamics, obtained from the theoretical calculations and during the development testing of the high power electric drives. Theoretical research was conducted, using the complete mathematical model of the servo drive, which included the equations of the control signal shaping path, electric motor, reducer and load. The equations of the control signal shaping network include only the characteristics of the compensating element in the assumption that all other delays in the transformation path are minimized. The electric motor equations are assumed in the classical form, taking into account the influence of the following main parameters on the motor dynamics: inductance and stator winding resistance, torque and armature reaction coefficients and rotor moment of inertia. Interaction of the motor with the multimass system of the reducer and load is presented in the form of force interaction of two masses – a reduced mass of the rotor and mass of the load through the certain equivalent rigidity of the kinematic chain. To describe the effect of gap in the kinematic connection the special computational trick, which considerably simplifies its mathematical description, is used. Efficiency of the reducer is presented in the form of the internal friction, proportional to the transmitted force. Calculation results with the application of the given mathematical model match well with the results of the full-scale testing of different specimens of servo drives, which makes it possible to use it for the development of new servomechanisms, as well as for the correct flight simulation when testing the aircraft control systems. In particular, based on the frequency response calculations of the closed circuit with the application of the given mathematical model, it is possible to define optimal parameters of the correcting circuit. Reaction on the step action with the various values of circular amplification coefficient in the circuit gives complete information on the stability regions of the closed circuit and influence of various drive parameters on these regions. Based on the conducted theoretical and experimental studies, the basic conclusions and recommendations were obtained and presented, accounting and implementation of which will provide high dynamic characteristics of the newly designed servo drives.

Annotation: Basic dynamic properties of the reentry part of the aircraft-type first stage were examined when turbojet engine is used in the recovery phase. Such configuration can be of interest because turbojets have considerably smaller rate of flow in comparison to rocket engines. Moreover, they are launched in the lower stratosphere or in the troposphere so that there is no need to place oxidizer supply on board. This recovery plan differs from an alternative rocket recovery system and, from our point of view, provides more efficient usage of the fuel stores because it doesn’t require the main propulsion to be started in the recovery phase. Besides the analysis of qualitative characteristics of the descend phase for this stage, the efficiency of a wing with moderate values of maximum aerodynamic characteristics and a turbojet was studied. In this case three ways for stage recovery were investigated. The first one implied unguided descend with zero angle of attack assuming that the stage is statically stable. This descend trajectory was considered as standard and was used to evaluate the efficiency of the wing and turbojet with relatively small propulsion. The second and the third design cases offered the gliding guided descend with turbojet being started only in the lower stratosphere. The last two cases used the same program for the angle of attack. The possibility to ensure permissible overload values at the critical points of the descend trajectory and acceptable values of kinematic characteristics at the earth surface tangency point are also of great interest. Thereby the program for the angle of attack was developed in a way that allowed kinematic characteristics on touchdown be as close as possible to the corresponding values, shown by civil and/or military-transport heavy aircraft. Simulation was conducted on Microsoft Visual Studio 2010.

Annotation: The main scientific and methodological propositions for designing single-stage guided missiles with main solid rocket motors that are intended for delivering payload to the given spatial point with required and specified kinematic motion parameters are defined. The aim of the article is to develop methodology for the early design phase to improve the basic characteristics of guided missiles, including formalization of complex problem to optimize design parameters, trajectory parameters and motion control programs for guided missiles capable of flying along the ballistic, aeroballistic or combined trajectories. The task is defined as a problem of the optimal control theory with limitations in form of equality, inequality and differential constraints. An approach to program forming is proposed for motion control in the form of polynomial that brings the problem of the optimal control theory to a simpler problem of nonlinear mathematical programming. When trajectory parameters were calculated the missile was regarded as material point of variable mass and the combined equations for center-of-mass motion of the guided missile with projections on axes of the terrestrial reference system were used. The structure of the mathematical model was given along with the calculation sequence of criterion functional that was used for optimization of design parameters, control programs and basic characteristics of the guided missile. The mathematical model of the guided missile provides adequate accuracy for design study to determine: overall dimensions and mass characteristics of the guided missile in general and its structural components and subsystems; power, thrust and consumption characteristics of the main engine; aerodynamic and ballistic characteristics of the guided missile. The developed methodology was tested by solving design problems. Applications of the developed program were studied to present the research results in a user-friendly form.

Annotation: When accomplishing the task of spacecraft orbital injection, the necessity arises of main engine multiple ignitions and consequently, long pauses between the ignitions are possible. As the propellant during pauses between ignitions is in the conditions of practically full absence of gravitation and can freely move over entire tank volume taking practically any spatial position, to ensure main engine guaranteed ignition the necessity arises to move the propellant into pre-start position. The propellant is moved to the supply lines by way of creating longitudinal acceleration which is done using inertial continuity ensuring means (thrusters). The time of full liquid displacement from one position into another is the most important parameter having an impact on propellant amount in the tanks and accordingly, on power characteristics of a stage. The theoretical calculations of hydrodynamic processes are connected with considerable mathematical difficulties caused by complexity of solving hydrodynamic problems of determination of liquid flowing with free surface taking into account surface tension of the liquid and many other geometrical, kinematic, and dynamic factors. Therefore, the most reliable data from solving these problems are currently obtained only on model hydrodynamic stands where it is possible to model liquid behavior in tanks in the conditions of variable gravitation. The paper presents the authors-developed procedure of calculating the full time required for propellant components deposition during rocket’s apogee stage flight and the procedure of selecting the modeling parameters (scale, time, and acсeleration) to ensure development testing in the conditions of limited test stand base. The use of the proposed procedure allows (in initial phase of launch vehicle development) determining the full time required to perform deposition with sufficient accuracy and thus optimizing the propellant mass required for operation of inertial continuity ensuring system, which in its turn, will allow increasing the payload mass to be injected.